Making furniture with your own hands is not only a great way to save money, but also an opportunity to put your creativity into practice!
It's about making coffee tables with your own hands. Too many side tables do not happen. They can be placed next to the sofa to place a vase of flowers or a mug of tea, used as a bedside table or as a stand for houseplant pots. However, monotonous wooden tables are unlikely to revive a dull interior. I want something stylish and unexpected ...
Stylish do-it-yourself table made of wooden slats
This bench can serve as a coffee table, extra seating or seating area. indoor plants. Such a piece of furniture will “fit” well into almost any interior!
Coffee table do-it-yourself photo
Materials:
Tools:
Step one: Using a hacksaw, cut the ends of two 2.5x7.5cm boards at a 45 degree angle. Cut out fragments from 2.5 × 5 cm bars, the length of which will correspond to the internal length of 2.5 × 7.5 cm blanks.
how to make a coffee table with your own hands. Photo
step two: Place 2.5x5cm blanks in the middle and 2.5x7.5cm around the edges. Make sure the ends of the inner rails are aligned.
Step Three: Measure the distance between the outermost 2.5x7.5cm boards and cut two blanks of this length from 2.5x10cm boards. They will serve as the lower supports for the bench. Secure them by screwing self-tapping screws into each longitudinal rail.
Step Four: Using the Kreg Jig, drill two pocket holes at each end of the support rails. These holes will be used to connect to the 2.5x7.5cm end pieces.
Tip: It's hard to give specific recommendations on how far from the edge to attach the Kreg Jig. This depends on the length of the screws used, the exact thickness of the board, etc. We advise you to pre-practice on unnecessary scraps of boards.
unusual coffee table with your own hands. Photo
Step five: Place 2.5x7.5 cm blanks along the edges of the structure. After making sure that their ends are at the same level, fix them with clamps.
Tip: If you are using softwood (such as pine) to make the table, place unnecessary scraps of boards under the clamp supports. Otherwise, traces of clamps will remain on the wood.
Step six: Securely attach the 2.5x7.5cm end pieces to the base of the bench by driving 3.5cm wood screws into the countersunk holes you made at the ends of the support rails earlier.
wooden coffee table. Master Class
step seven: Measure the width of the finished base to determine how long you need to cut 2.5 × 7.5 cm blanks for the ends of the bench. We recommend that you take a sip with a small margin in length, and then take your time to grind off the excess until you achieve the perfect fit.
Step eight: Moisten the ends of all rails with water and apply a small amount of Gorilla Glue.
Step nine: Install the end boards in their intended place and wrap the entire structure with a belt so that it does not fall apart until the glue dries. For reliability, you can additionally fix the ends with a few finishing nails.
Step ten: Sand the surface of the bench with 120 grit sandpaper to eliminate any unevenness at the joints. All gaps in the seams and recesses from the heads of nails (the latter must be recessed into the wood without fail) fill with putty. When the putty is dry, sand the surface again, this time with 220 grit sandpaper.
Step Eleven: Paint the bench. We advise you to sand the surface again before painting with 400 grit sandpaper and water.
Step twelve: On the lower support rails, fit the special mounting plates for attaching the legs. When fixing them, make sure that you drill holes in places where there are no already screwed screws. The distance from the mount to the edge of the bench base should be about 2.5 cm. Screw the legs themselves into the mounts.
Coffee table made of copper pipes. Master Class
The material for the manufacture of the next table can, perhaps, be called the most unexpected. This time we decided to tell you how to make a table out of ... copper tubes with your own hands.
Materials and tools:
The figure below shows all parts (pipes (A-E) and various fittings (F-H)) with their dimensions and quantities. All that's left for you to take pipe cutter and sit in front of the TV, which will brighten up the tedious cutting process a little. It's not hard, just a little boring. 😉
When all the blanks are ready, you can begin to assemble the lower part of the table. How to do this is shown in the figure.
Having collected the lower tier, you can proceed to the upper one. The only part not listed in the parts list are four pieces of 2.5 cm pipe that are placed in tees at the top of the corner posts. Without these inserts, you will not be able to wear decorative caps, because the latter have the same diameter as the tees.
Reliable connection of the tubes to each other will ensure glue, but we recommend applying it only after the preliminary assembly of the structure, i.e. after you make sure that all the cut tubes are of the right length and fit well with each other.
Wooden shelves, which you can pre-paint if you wish, are fixed with special clamps that are placed on the underside of each board. Now you are ready to decorate your home with your new DIY table!
DIY lightweight cement table
Concrete countertops and other interior elements have recently become more and more popular. However, for all their attractiveness, they are not without a number of shortcomings. First, pouring large amounts of concrete can sometimes be quite expensive. Secondly, if we are talking about small side tables, another serious problem comes to light - such furniture turns out to be too heavy. On the one hand, there is a desire to get a good, solid thing, on the other hand, I want to be able to move a table made by myself without the help of professional movers. The found solution can be considered an insight.
Materials and tools:
Step one: Mark and cut the foam sheet. From a 120x240 cm piece, you can cut 18 squares 40x40 cm. Stacking them on top of each other, you get a 40x40x45 cm box.
do-it-yourself foam board. Photo
step two: Glue the cut pieces. 3M Super 77 spray adhesive is ideal for this. It is best to perform this stage of work outdoors. Don't forget to wear gloves and a long sleeve shirt. Apply an even layer of glue to one side of the first square, then do the same with the second. Wait ~15 seconds, then connect the squares, making sure their edges are joined. Repeat this until all the square blanks are connected into a single whole. Wait about 30 minutes before proceeding to step 3.
Step Three: Now the most interesting thing ... giving the resulting parallelepiped the outlines of the future table. We decided to make a table in the shape of a cylinder. You can come up with something more original or, on the contrary, keep the original block with right angles. Cutting foam is easy and fun. At first, your design will have a rough, angular look, but don't worry! After the table has been given the desired shape, it will be time for grinding. Using 36 grit sandpaper will quickly smooth out any bumps. As you get closer to the ideal, gradually move to sandpaper with a finer grit size. Don't aim for a super-smooth surface, at this stage it's just a matter of getting the desired shape.
Step four: The surface of the future table is polished, it is time to cement it. The first coat, applied throughout the foam mold, will fill in the voids and texture of the foam. You only have ~20 minutes, so act fast so you have time to iron out the bumps. When the applied cement mortar dries, you can apply the next layer. The number of layers depends on how smooth and even the surface you want to have in the final (as a rule, four to five layers are required). It should be remembered that the smoother the surface of the final layer before it dries, the less it will have to be sanded!
Tip: When cooking cement mortar follow the manufacturer's instructions. You should not prepare more mortar than you need to apply one layer (for example, we used 220 ml of water and 450 g of cement). Make sure you don't forget to cover your workbench or workshop floor as this is a messy job.
Step five: After the last layer of cement has dried, you can sand the surface if desired. We wanted to achieve a glossy finish, at least on the top of the table, so we sanded it down using a variety of grit sandpaper ranging from 100 to 2000.
Tip: If you are planning this operation, get a protective mask that will help you protect your lungs from cement dust.
(The table made in this project turned out to be very strong and strong, but at the same time it weighed no more than a kilogram.)
Do-it-yourself stump table
The material for the next table sometimes literally lies underfoot. Even residents of megacities, if desired, will be able to find a suitable stump.
log table. Photo
Materials and tools:
- wooden block;
- white acrylic paint;
- manual grinder;
- chisel;
- hammer;
- decorative upholstery nails;
- molar tape.
Step one: Find a table base! This should not be an old rotten stump, but a freshly sawn block of wood. Let it dry for at least 6 months (there's nothing worse than waiting, but it's necessary) until the bark begins to peel off the trunk.
Step two: Using a chisel, gently remove the bark from the log in a downward motion. If the stump is dry enough, you won't have to use too much force.
Step three: Using a sander with medium grit sandpaper, sand the surface, removing the remaining bark and smoothing out sharp corners. Do not forget to sand the surfaces of the lower and upper cuts. Wipe the wood with a damp cloth.
Step Four: It's time for painting. We used a white semi-gloss paint that includes a primer (we needed three coats for full coverage). You can choose a different type and color of paint, focusing solely on your taste. Don't forget to pre-prime the surface of the wood. Make sure you don't forget to finish the bottom cut.
Step five: Get your decorative nails ready. Apply a strip of masking tape along the top edge of the side surface of the block of wood, thereby marking the place where the first row of nails will be located.
Step Six: Using a hammer, drive in the first row of decorative nails. To ensure that the distance from them to the upper edge is the same throughout the “line” of nails, use the strip of masking tape you previously glued as a guide. After the first row is completed, repeat the same with the second and third row of nails (we needed almost 150 studs for three rows).
Tip: Cover the underside of the stump with furniture felt so you can move the table around the room without damaging the flooring.
The work is done. You can use the new piece of furniture and be proud that you made this charming coffee table with your own hands.
Coffee tables: do it yourself
Wooden table: how to make?
Many people are interested in how to make a wooden table with their own hands to get a model with an original appearance. Let's consider one of the options.
To make an original coffee table with your own hands, you should take timber with a section of 5x10cm. It is sawn into parts of the following length: 130cm - 9pcs, 21cm - 12pcs, 34cm - 2pcs.
The prepared beam is placed in three rows, leaving room for attaching the legs.
Remove the top two rows. The timber in the third row is slightly shifted to get an interesting appearance. Next, mark the places for attaching the transverse parts.
Lay the extreme bars of the second row and mark the places of the cuts. Then cuts are made circular saw or a hacksaw with a chisel.
The bars of the second row are fixed with screws.
The third row is laid, the parts are shifted and fixed.
An empty space is formed under the tabletop, in which they are fixed legs.
Wood is processed protective composition that preserves the grain of the wood.
The original model of a wooden coffee table with their own hands
First, to make a table with your own hands, prepare boards: 6pcs - 22.5x45cm, 2pcs - 22.5x41cm, 8pcs - 20x4cm, 8pcs - 40x4cm.
Planks 20x4 and 40x4 are glued in pairs. To ensure they are securely glued, they are clampedclamps.
While the blanks for the legs dry, collect box from the rest of the details. They are connected with carpentry glue and nailer.
legs attached to the box with countersunk screws. At the bottom between the legs put the crossbars.
Lid for a table made of wood is also made using boards 22.5x45cm. They are glued together, and then the resulting square is sawn into two triangles.
One triangle is fixed with screws, and rails are fixed on the second so that it is removable.
All parts are sanded and painted.
Stylish coffee table. Master Class
They start making a stylish table with their own hands from marking the sheet Chipboard 16mm thick. The center is found on the sheet at the intersection of two diagonals.
A nail is driven into the center, to which a thin rope or a harsh thread is tied.
Tie a pencil to the free end. This allows you to draw a circle.
If you want to make a table with your own hands not round, but more interesting, then the shape of the circle is changed by drawing bends.
The tabletop is cut out jigsaw or reciprocating saw.
Edges are processed sandpaper.
legs fasten with screws. If they are inclined, then the slope should be outward.
Table surface stain V desired color.
Simple shape coffee table
To make a coffee table with your own hands, take boards 40x15cm - 2pcs and 50x19cm - 2pcs. In addition, you will need legs and mounting plates.
On one of the boards they fix more plates for fixing legs. From the edges should retreat a little.
Side and upper part the tables are fixed with wood glue.
It dries for about half an hour.
Do-it-yourself log table
A do-it-yourself coffee table with such an appearance will become a decoration for a summer house or country house. Begin work with the assembly of the frame. To do this, take sheets plywood two centimeters thick. A base with dimensions of 60x80cm is cut out of them. A box 68 cm long, 45 cm wide and 40 cm high is attached to the base.
do-it-yourself log table. Photo
After that, cut thirty pieces of round logs 45 cm long and twenty-four round cuts, the thickness of which is 3 cm.
Harvested logs are attached around the perimeter of the box. Attached from below to the base rollers. They are installed, departing from the edge by three centimeters.
In addition to glue, it will be useful to fix the logs on the screws from below.
Installed on the box plywood cover. Rounds are glued on it. The space between them is filled with wood putty, which does not shrink when dried. Apply it in stages so that the previous layer has time to dry.
After the putty has dried, the surface polished. To do this, use a surface grinder. After that, the log table can be used.
Rustic table
If you are interested in how to make a table from wood cuts with your own hands, then you should read the instructions.
They start making such a coffee table with their own hands by choosing the right material.
Selected saw cut check for availability interesting details or parts to be removed.
Unnecessarily rough, protruding parts are cut off. On the side where the countertop will be, the surface align.
For work use cleaver, which moves at an angle of forty-five degrees.
The sides also need to be aligned.
All surfaces grind, using ever-decreasing grit.
Glossy varnish mixed with resin in equal proportions.
The resulting composition is applied to the wood in a thick layer. It will dry for a long time. If gaps appear during the drying process, they must be filled.
bottom side clean up. If there are voids in the tree, then they are filled with resin gradually until the hole is filled.
If there are air bubbles in the dried resin, then the surface is heated with a heat gun or burner.
A second layer of resin is applied and again left to dry for two days. The entire surface of the countertop must be glossy.
At the handles of the ax, a part is cut off at an angle of 22 degrees. The surface is sanded and painted in the desired color.
Mark out places for legs and make holes.
Glue is poured into the holes and the legs are installed. Each has a special pad.
White coffee table
They make such a coffee table with their own hands from plywood And glass. First, prepare a drawing and determine the dimensions. Then proceed directly to manufacturing.
handmade coffee table Blueprints
Plywood acts as a countertop box with partitions, covered with glass on top. Triangular legs are attached to it.
At the box, you can make a door to access what's inside, or raise the glass.
legsfor a table with your own hands, it is better to cut it out of fairly thick plywood. It must be remembered that double legs are easier to make than more single ones.
When all the parts are ready, they are assembled together and fastened. The table is painted or varnished.
DIY pallet table
If you know how to make a table from pallets with your own hands, you can get interesting option home furniture. Pallets must first be sanded, sawn into pieces and primed.
pallet table. Instruction
A table is assembled from the prepared material. To do this, attach the legs or wheels. The pallet itself or the surface assembled from individual boards can be used as a table cover.
After all the parts are connected, the structure needs to be painted or varnished. After that, the pallet table is ready.
The second version of the table from pallets
To make such a table with your own hands, you will need one or two pallets. First, you should draw a sketch of the future product, taking into account all sizes.
The table will have a shelf for small things under the tabletop. The design is assembled from prepared parts.
The surface is painted with black paint, but this is not the only possible variant. There are many other decorating possibilities.
Coffee table stand
How to make a table out of copper pipes with their own hands, may be of interest to many craftsmen.
Pipes are first marked and cut. Then they are smeared epoxy glue and assemble the base for the table.
This base is applied to the board and the attachment points are circled. In these places you will need to drill holes by pipe diameter.
Four holes are drilled, but not through.
The board is impregnated polyurethane and cover stain.
The rest is collected from the pipes frame.
Legs and base cover paint in the color of the table top.
Made from a piece of cloth pocket, which is hung on the transverse parts of the legs.
All parts are assembled together, adding epoxy glue for reliability.
DIY marine-style table
Such a table from the old window frame looks very romantic. The frame is cleaned of dust. If required, replace the glass.
wooden surface stain white acrylic paint. After drying, the paint layer is treated with sandpaper so that the wood comes out. Also available in blue and white.
To make legs, take cutting and sawn into pieces of 34 cm. After that, it is treated with sandpaper to remove roughness.
The blanks are drilled in four places. Next, each leg is attached to the base, and the base with legs to the frame. All this is done with self-tapping screws.
The legs are covered with coarse rope.
For cleaned and defatted glass glue sea souvenirs and seafood. From above they must be covered with glass, which is cut out in the workshop to fit the frame.
Make a loop at one end of the rope. The rope is glued around the perimeter of the frame, leaving the loop free. When the second end reaches it, they tie an interesting sea knot.
Do you love designer clothes, but sigh in frustration when you look at the price tags that adorn them in stores? Try to become a designer yourself. Think it's difficult? Nothing like this! By following the instructions, you can easily create do it yourself original a piece of interior from improvised materials. And we propose to start with coffee table- such a simple, but very important subject furniture. Believe me, at such a table you will be happy to give tea to your guests, who will admire your skills. In addition, by creating a coffee table with your own hands, you will literally fill your house warmth and put a piece of your soul into it. So it's definitely worth a try.
DIY coffee table in a marine style
Romantic idea. All year round, drinking your favorite drink at this table, you will remember the warm sea, the gentle surf and the moonlit path. " Nautical» a table is tenderness, sophistication and originality in the heart of your home.
How to do?
1. Take an old window frame and clean it of dust and dirt. If the former glass cracked, insert a new one, then get rid of the layer of the old paints and sand the surface. Next, you should remove the metal corners, which additionally fix the details. frames.
Ready! Enjoy your creation and give joy to your guests!
Table-suitcase for travel lovers
Very original solution for an old favorite suitcase that has seen other lands with you and that you don’t want to throw away because of the memories.
How to do?
To get started, go to the store where you will need to purchase furniture legs ( wooden or metal). If you want to make a mobile table - then you need to take the wheels. You will also need plywood, screws and a screwdriver.
Now we make markings on the bottom of the suitcase for future legs and drill holes. Since it will not work to attach the legs to the fabric, we put plywood inside the suitcase, make markings on it through the holes and also drill it. Now we attach the mount to the bottom of the suitcase and fasten the legs. Using hot glue, glue the felt inside the suitcase.
To give the table an original appearance, reminiscent of distant travels, you can decorate it with stickers made in the form of stamps, or decorate it at your discretion.
That's all - an unusual coffee table is ready! By the way, there are a lot of options for turning suitcases into tables: by choosing the legs to your liking, you can make a table in style retro or classical. You can not attach the legs at all if you have a massive suitcase - it will look truly incredible: such a table will bring a sense of adventure and adventure into the interior, the spirit of travel and unexplored distant countries.
Log table for nature lovers
We take wooden bars(in this case, birch) of the same height and width, only 32 pieces. You also need to take the base for the table, legs (4 pieces), putty to match the wood, a screwdriver and glue designed for wooden surfaces.
First you need to assemble the base for the table, then glue wooden bars around the perimeter, and sew up the middle with cardboard. Then we fasten the legs to the bottom. Next, we glue thin wooden dies to the inner surface - thanks to this, it will seem that the table is completely wooden. Now we take the putty and carefully close up all the voids, after which we overwrite until an absolutely flat surface is created. Voila! Now you are the owner of an extraordinary table that will become the highlight of your interior.
If you like the idea, you can create other tables according to this scheme, using, for example, branches instead of bars. To create such a table, you need to take a plywood box, painted black paint, the size of which is 40x40x60 cm (or any other size at your discretion).
To glue the frame, we take branches, from which we first remove the loosely holding bark (we do this with sandpaper). What is the procedure for gluing: first we glue the branches on the long side of the table, and then we select wooden dies and, as mosaic, lay them out on the ends. The thickness of the dies should be approximately 1 cm, they can be cut with a parquet or circular saw. And finally - install the glass, which will be the countertop. If desired, by screwing wheel supports to the table, it can be made mobile.
Using the same technology, you can create many more unusual pieces of furniture. You can lay out the branches horizontally and then you get such a wonderful table. Such furniture looks not only very original, but also incredibly stylish.
original pallet table
An idea that came to the mind of someone truly brilliant. It would seem that you can come up with pallets, which are probably lying around in every dacha? And you can make them a very convenient and functional element of the interior.
How to do?
To get started, collect all the tools you need for your idea: the pallet itself, a drill, clamps, a hammer, screws, a nail puller, glue designed for wood, wheels, soap, a primer, a screwdriver. In addition, take paint brushes, a petal brush head with abrasive bristles for a drill, varnish and a colorless primer.
First of all, you should take a drill with a nozzle designed for wood processing, and clean the surface of the boards from contamination with it. Now carefully disassemble the sanded pallet into parts. Lightly tap the rusty nails with a large hammer and carefully pull them out with a nail puller. Glue the broken pieces of boards with wood glue. At this stage you will need clamps. They need to carefully clamp the boards and wait until they dry out.
Now the parts prepared for the countertop need to be nailed and glued on the reverse side, then clamped with clamps and wait until they dry.
Then cover the table with a colorless primer, and then varnish. Next, on the back of the table, mark the places for the screws to attach the wheels. Drill holes for the fasteners. In order for the screws to easily enter the wood, grease them with soap. Using a ratchet, you can quickly and conveniently tighten hex screws.
Stylish, compact and quite functional table is ready!
Table from boxes
Another one original idea captivates with its simplicity and surprise - well, who would have thought to build a table from boxes? But it has come, and now you yourself can create such an unusual piece of furniture at home. Surely you yourself will be delighted, and your guests will appreciate the originality of this idea.
How to do?
Take 4 wooden boxes, sandpaper, varnish c water base, roller and brush, dowels, 10 mm plywood sheet, PVA glue, 4 wheels and self-tapping screws.
First you need to sand the boxes and varnish them. Then, using a drill with an emphasis, make holes at the ends of the boxes. Using wood glue, you need to fix the dowels in the attachment points and connect the ends of the boxes to each other. Attach the wheels to the plywood sheet, and then attach the sheet to the boxes with self-tapping screws. The table is ready!
These extraordinary things can be created from quite ordinary materials. Having imagination and a desire for originality and comfort in your home, you can easily work wonders. Look around: maybe old window frame has every chance of becoming interesting element interior?
Or maybe a huge wooden reel from an industrial cable that can become an elegant piece of furniture?
For starters, amateur self-manufacturing furniture, it is worth learning how to create a stool, because this is the easiest. And then comes the time to study the issue of creating a table.
Table designs vary, however, the simple version is very similar to the process of making a stool.
A simple table for use in the country or during a picnic can be assembled in just a few hours. To do this, you need a hacksaw, hammer or drill.
However, a table based on a similar approach can be made for living quarters. Because it is able to perfectly replace the current very large version bought at a retail outlet or furniture store.
The process of self-creation of the table is also interesting from the other side, since with the help of it there is freedom of the author's creative expression. It can be imagined as a noticeable element of the interior of the room.
The creators of handmade amateur furniture are called carpenters for a reason. They do not apply the usual definition like: sofas or bedside tables, or maybe cabinets.
Having gained experience in this area, over time it will be possible to create exclusive types of tables with advanced characteristics.
Now consider the issue of self-creation of tables based on wood.
Wood is distinguished by its purity and availability, in addition, it is not as difficult to process as other materials. It conveys the maximum energy of the aesthetic filling of the style of the living room.
Due to its properties, it is condescending to the mistakes of beginners in the field of self-creation of furniture. However, thinner versions of the tables will require an advanced level of skill.
To begin with, having learned how to work with wooden things, then it will be easier to use as a material: glass, plastic or even metal.
Selection of tools and premises for work
To engage in independent creation of tables or other wooden elements furniture, it is necessary to use only non-residential premises.
This is due to the specifics of working with wood. It leads to the formation of a large amount of dust, chips and other waste.
And the process of toning or creating protection for a stain-based material can form dangerous emissions into the air. Actually, nitro-varnishes can also be dangerous.
Because of this, for a personal carpentry workshop, you will have to take care of airing the room. Experts advise creating artificial ventilation of the room.
Many people use the garage for this, however, production waste can pollute or damage the car because of this, this is not the best option.
Carpentry tools belong to modern and traditional types
For the most part, you can start with a simple carpentry tool, however, later modern versions may be required in the form of:
- A rotary version of the miter box, which helps to create saw cuts based on two planes, adhering to the required size.
- This tool will open all your beneficial features, primarily with a bow saw. This couple is considered universal, it can be useful for many jobs.
- A manual version of the universal electric jigsaw, featuring a tilting shoe to help create a cut based on the desired angle in relation to the vertical plane.
- Disc version of the grinder. It will help beginners complete the surface treatment of wood in about 5-15 minutes. An experienced carpenter, along with sandpaper, can do the same job in about an hour.
And there is also a conventional belt grinder for grooves with recessed places, which is distinguished by a protruding version of the working part.
Such tools are distinguished by the price and narrow specialization of the work performed, experienced craftsmen recommend to take them for a short rental period.
The best specialists, using various sanding machines, can even create the effect artificial aging wood, however, is a very difficult job, as for beginners.
Which tree is the best?
To create a wooden table, any wood that has an average resistance to the rotting process will work well, however, you should refrain from soft versions like: poplar, willow, ailanthus, aspen, and even alder.
From domestic types of wood it is best to use:
- soft options in the form of pine, fir, cedar, horse chestnut, plane tree, juniper or spruce.
- solid in the form of an ideal oak, suitable for many works of beech, maple, walnut or ash, larch, as well as fruit species represented by apples, plums, pears, apricots and quince. And also here it is worth including elm and mountain ash.
- rather hard species based on acacia, yew, stone birch, dogwood and boxwood.
Conclusion
You want to decorate the table and probably all types of furniture created by yourself with an artistic version of the painting, and not with ordinary stripes.
However, over time, the pattern may deteriorate, so that this does not happen, it is necessary to rub the paint into the depth of the tree before the varnishing process. This can be done on the basis of technology - glazing. We are talking about layer-by-layer rubbing of the paints used.
DIY table photo
Coffee table - at first glance, not the most necessary furniture. Therefore, its acquisition is endlessly delayed.
But it is precisely such items that make the interior truly cozy and comfortable. Therefore, we share ideas that will tell you how to make a stylish coffee table with your own hands and not go broke.
1. Democratic and accessible
A table made of boards and boxes.
To make such a table, you will need a pair of metal or plastic boxes and two large boards. Be sure to securely fasten the structure.
2. For the smartest
Elegant mini table.
Books with beautiful covers and a small glass for the tabletop - that's all the materials for such a coffee table. Books must be glued together, and the glass can be fixed on them with silicone glue, which becomes transparent after drying.
3. Ordered chaos
Original coffee table with your own hands.
A coffee table made of flat elements fastened together in a chaotic manner is an idea that is easy to implement. Wooden saw cuts, parts of boards, large books are suitable. 
Table made of wooden saw cuts.
4. Industrial style
An industrial cable reel can become a table.
A reel for industrial cables is a thing that cannot be found on every corner. But if you are still lucky enough to become the owner of this item, you can make an excellent coffee table out of it. 
Functional coffee table.
5. Table for motorists
Reliable tire table.
A coffee table made from a car tire will last long years. But it is desirable to use the tire without damage. It remains only to paint it, fix the countertop and legs.
6. Wooden table almost free
Making a coffee table with your own hands will turn out from a pallet.
Ordinary pallets, which can be purchased for a penny, are an excellent material for making furniture. A little imagination, and the wooden coffee table is ready.
7. The second life of old boxes
Large drawers - the basis for a coffee table.
Another way to become the owner of a coffee table made of natural wood is to use old boxes as a material for its manufacture. Four large drawers fastened together form a stylish table.
8. Extravagant chic
Asymmetrical coffee table.
Especially original, but at the same time luxurious, looks like a coffee table on asymmetrical legs. The tabletop is made of a thick board or a wooden saw cut.
9. From the cottage - to the living room
Barrel table.
Big wooden barrel easily turns into a coffee table. It must be cut into two parts, and then attach the countertop and legs to one of them.
10. Roomy and functional table out of the box
Functional table out of the box.
A household box made of plastic or wood can also be used as a coffee table. In order for the table to be mobile, you can fix small wheels on its bottom.
11. Warm table
Metal radiator furniture.
An old heating radiator is a reliable basis that will help you make a coffee table with your own hands. You just need to paint it in the desired color, attach the wheels and put thick glass on top.
12. From the interior door
An old door might come in handy too.
An interior door that has served its time becomes a material for making a coffee table with your own hands. It must be cut into several parts and fastened together.
13. If it’s a pity to quit and it’s hard to carry
Coffee table from a suitcase.
An old suitcase can become an original coffee table top. You just need to attach legs to it.
14. Brutal elegance
Original pipe legs.
An affordable option for making legs for a coffee table is ordinary plastic or metal pipes connected by fittings. Such furniture will perfectly fit into the interior in loft style.
15. From an ordinary wooden beam
Wooden table from a bar.
A wooden beam, folded in a checkerboard pattern, will become a countertop for a homemade coffee table. Legs can be made of thick metal wire.
The coffee table is a decoration and highlight of the interior. A handmade item is doubly appreciated. It can be made from wood, glass, plastic and other materials. It's not difficult at all. You will need drawings and a little patience. A beautiful table will become a place where you can relax and read the press or sit with friends over a cup of tea. Step-by-step instructions with photos will simplify the manufacturing process.
Preparatory work
In order to make a coffee table on your own, you will need not only drawings, but also materials with tools. Stock up on the following building supplies:
- wood (solid);
- water-based varnish;
- solvent;
- acrylic paint;
- brushes;
- self-tapping screws;
- jigsaw;
- screwdriver;
- grinder;
- milling cutter;
- drill.
As for wood, the best choice there will be an array of pine 2.5 cm thick. In accordance with the drawing, the parameters of the coffee table, which is planned to be made by hand, are 1.5 m x 0.5 m.
Attention! The table does not require separate legs.
Lacquer needed to cover finished construction, in total it will need about 0.3 liters. Acrylic paint is best purchased with glitter. With its help, you can give an unusual look to the interior. The assembly of the table will be carried out using self-tapping screws. Their size should be 4 x 60 and 4 x 40 mm. As for the rest of the tools and materials, there are no special requirements for them.
Mounting Features
The first step in the manufacture of a coffee table is the selection of drawings and sawing out the appropriate parts. Suitable schemes can be found on the Internet or you can make your own.
Attention! Ready-made drawings are much easier to use and the process of making a table will be completed faster.
So, when all the details are ready, you can start assembling the future interior decoration.
- All joints and roughness of wooden parts must be primed. This can be done with wood glue or PVA. Then let all components dry completely.
- Planks and legs should be fastened with self-tapping screws indicated in the list of required materials.
- The resinousness of the coffee table is easy to remove with a solvent. The most popular remedy is white spirit. Moisten a dry cloth with a little agent and wipe the surface of the table.
Advice. Do these manipulations in an open space, because in the apartment this smell will not disappear soon.
- The table is almost ready. But it needs to be decorated. To do this, you need to mix varnish and acrylic paint with shiny splashes. Cover the entire surface of the table.
- After the paint and varnish have dried, the coffee table can be placed indoors and used for its intended purpose.
Table made of wooden boxes
This is the simplest and original way make a decorative table. designer item self made rightfully take a place in the living room or bedroom. To make a table, you will need wooden boxes. It's wood, not plywood. Wood has good performance qualities, which cannot be said about plywood.
But still, this material is also required for a coffee table from drawers. Take a few minutes of instructions and you will definitely succeed!
- Prepare a sheet of plywood. This is done in order not to burden the structure. Wooden boxes are not a perfect geometric object.
- In this regard, the boxes should be laid on a horizontal, flat surface. Before cutting the plywood sheet, draw the outlines. And cover the sheet of plywood with varnish or stain.
Advice. For a coffee table made of drawers, you will need wheels. They can be purchased at any hardware store or hypermarket. It is best to buy wheels that are small and low.
- The wheels should be fixed at the corners, and the drawers should be attached to the bottom tabletop.
- It remains to varnish the coffee table. After applying the varnish, you need to let it dry and only then cover it with a new layer. This procedure is repeated several times.
Advantages and disadvantages of wooden tables
Wooden tables are a popular option that will easily fit into any interior. It is only important to choose the right shade that will be in harmony with the rest of the furniture. Like all objects, such designs have their positive and negative sides. The pluses include:
- a large selection of wood (soft, hard breeds);
- variety of shades and textures;
- ease of manufacture and ductility of the material;
- naturalness and environmental friendliness;
- versatility.
Apart from positive sides, it is necessary to note the shortcomings. There are few of them, or rather, only two: the high cost of the material and susceptibility to mechanical actions (scratches, abrasions, etc.).
Popular ideas for making coffee tables out of wood
Instances made of wood have always been environmentally friendly and beautiful. And how much interesting ideas can be made a reality! It would seem that a simple table made of wood, what can be original in it? We offer you several popular options for making a coffee table.
- Pallet table. For its manufacture, ordinary pallets are required, to which the wheels are fixed. Distinctive feature such a design - a small height. It is enough to fasten the wheels and the table is ready. Some go further and decorate it with a countertop and various shelves.
- table from old door. If you have recently changed doors, then the old ones can be used as material for making a coffee table. The door needs to be sawn into three parts: a countertop and two legs. Between themselves, they are attached by means of corners.
- Table made of wooden logs. Everything is very simple. You need to pick up or cut the same blocks of wood. A plywood base is taken. Movable wheels are attached to its lower part, and logs of trees are attached to the top. The material used is birch, aspen or beech.
- Stump table. It is enough to attach wheels to it, varnish it and the decorative table is ready.
A handmade coffee table is an original way to decorate a room. The design, dimensions and other characteristics of the item are completely dependent on the selected drawing and your preferences. It is worth noting that for the manufacture of the table, you will need a minimum amount of materials.
DIY wood coffee table: video
Wooden coffee table: photo
