One heating circuit, built-in autonomous automatic SIT 820 NOVA piezo ignition. The boiler does not require an electrical connection, is completely autonomous, can operate indoors, open system heating the building. Not picky about the coolant, it is allowed to use non-freezing liquid when installing a closed system, at a pressure of one and a half bar.
Features of the floor-standing device Lemax Premium 40
The heated area of a building, house, cottage is 400 meters with a standard ceiling height, three measures.
The Premium 40 boiler is a welded steel structure that forms a water jacket around the entire perimeter. At the bottom of the boiler, in the opening of the combustion chamber, a gas burner device with controls is installed. At the top of the boiler there is a gas outlet pipe to remove combustion products from the firebox.
On the back surface of the boiler there are threaded pipes designed to connect the boiler to the heating system. Regulation and maintenance of the set temperature is ensured by a thermostat that modulates the flame of the main burner, equipped with a knob with divisions, which is installed on the front panel of the burner.
Thanks to the coating with anti-corrosion enamel “CERTA” (exposure temperature 750°C) and treatment with an inhibitory compound, the heat exchanger is protected from aggressive factors: salt solutions, mineral oils.
The Premium boiler does not require connection to the electrical network.
Equipped with original components of the gas burner device and a gas valve from the Italian concern “SIT”, as well as a “POLIDORO” injection micro-torch burner.
- The presence of a protection system against overheating, interruption of draft, soot formation, and also against blowing out of the boiler.
- The Premium 40 boiler is convenient to maintain due to the use of removable cladding elements and profile equipment.
- Ease of cleaning the boiler due to the use of a removable top panel.
- Advanced safety protection system (heat exchanger overheat sensor installed).
- Maximum efficiency with a steel heat exchanger.
- The most economical mode when installing a room thermostat.
- Increased heat exchange area.
- Changes in the design of the turbulator for maximum retention of exhaust gases.
- Increased primary and secondary air flow.
- The Premium boiler has the ability to switch to liquefied gas.
- Large diameter heating outlet pipes, diameter 50 mm.
- The boiler operates in natural circulation systems.
- Installation of a circulation pump is permitted.
- Boiler warranty from the manufacturer is 3 years.
Technical characteristics of the steel floor-standing boiler Lemax Premium 40 series
Maximum gas consumption for the LEMAX PREMIUM 40 boiler with the GGU 45 gas burner device = 4.5 m³/hour.
OPERATION PROCEDURE
The room in which the Premium 40 boiler is installed must be provided natural ventilation. It is prohibited to cover ventilation duct grilles.
To turn on the boiler, it is necessary to check the filling of the heating system with water, check for the presence of draft and select the desired procedure, determined by the power of the boiler and the safety automation used.
For boilers with a power of 40 kW and above, with a gas burner device based on the Italian automatic “SIT 820 NOVA” and a Polidoro injection burner.
ATTENTION!
Make sure the control knob is in the "off" position
The procedure for igniting a GGU 45 equipped with an automatic SIT 820 NOVA.
Setting the control knob to the required position is done by lightly pressing and turning to the desired position.
In the initial (off) position, the control knob is in the “dot” position. The pilot and main burners are off (the gas supply to them is blocked).
To ignite the pilot burner, the control knob is moved to the “spark” position.
In this position, keep the control knob pressed all the way, and at the same time press (if necessary several times) the piezo igniter button until the pilot burner lights up (look through the inspection window). After the pilot burner lights, hold the knob pressed for at least 30 seconds, after which the knob is released and moved to the “torch” position. When starting the boiler for the first time, it is necessary to keep the boiler on the pilot burner for at least 3 minutes, and then switch it to the “torch” position. When the control knob is moved to the “torch” position, the gas supply to the main burner is blocked.
The device is turned off by turning the knob to the “dot” position. In this case, the pilot and main burners (if lit) will go out.
If the control knob, after being moved to the “dot” position, is immediately set to the “spark” position, then the burner will not ignite until the so-called internal automatic lock is blocked more than once. The locking is removed automatically after the thermocouple has cooled down (approximately 60 seconds) after moving the handle to the “dot” position.
The coolant temperature is adjusted using the temperature regulator knob on the boiler body.
Boiler automation Lemax Premium 40
Design of the steel floor-standing boiler LEMAX PREMIUM 40
INSTALLATION, PREPARATION FOR WORK
The volume of the room in which the boiler is installed must be at least 8 m3. The distance between the boiler lining and the walls must be at least:
- – 150 mm at the rear;
- – 100 mm on the right and left;
- – 1000 mm at the front.
Natural ventilation must be provided in the room in which the boiler is installed.
When installing the boiler to the heating network, it is necessary to lay a sheet of non-flammable heat-insulating material on the floor, a sheet of iron on top, and install the boiler on it. The Premium boiler must be connected to the gas pipeline through dielectric insulation.
The connections of the boiler to the heating system and the gas main must be threaded, allowing the boiler to be disconnected if necessary. If a Premium boiler is installed to replace an old boiler, it is necessary to flush the pipelines and radiators of the heating system to remove rust deposits, scale and sediment. If these requirements are not met, deposit products (rust, sediment) are transferred to the boiler, which significantly complicates the circulation of the coolant and reduces the heat transfer of the Premium 40 boiler. In this case, claims regarding the temperature indicators of the coolant during operation of the boiler are not accepted by the manufacturer.
With increased heat consumption of the room (thickness of the external walls of the house, integrity of windows and doors, distribution of heating system pipes in attics, attics that are not insulated, exceeding its area or significantly exceeding the coolant capacity - the number of radiators, pipes) from those established by the standards, the temperature of the coolant may do not reach 80 °C, which does not mean the boiler is defective.
Approximate amount of coolant in the heating system for a Lemax floor-standing boiler:
- Premium boiler 35 – 500 liters;
- Premium boiler 40 – 600 liters.
The exact amount of coolant is determined in the heating system design.
For correct filling and feeding of the system, as well as for closed heating system be sure to install a relief safety valve of 1.5 kgf/cm2 (bar) at a distance of no more than 150 mm from the connection point of the valve to fill the heating system.
The expansion tank is installed at the top point of the main riser, preferably in a heated room. Do not install the valve on the signal pipe.
Horizontal sections of heating system pipelines must be made with a slope of at least 10 mm per 1 meter towards the heating radiators and from them to the boiler. This is done to ensure free release of air when filling the system with water and eliminate the occurrence of air locks.
Pipelines, heating radiators and their connections must be sealed; water leaks are not allowed.
Warranty obligations of the LEMAKS plant for a gas floor-standing boiler of the PREMIUM series
In case of failure of the Lemax Premium boiler to operate during the warranty period, subject to compliance with the requirements, the consumer has the right to free repair, and in the case of a manufacturing defect in the heat exchanger, replacement of the boiler. Warranty repair The boiler is manufactured by specialized service centers or gas services. Based on the results of the repair, a warranty repair certificate is issued.
For heating residential and non-residential premises, medium and large areas, floor-standing gas boilers are most often used. They are among a huge range of heating equipment, which also includes solid fuel, diesel and electric boilers, have a low cost of ownership. It consists of the relatively low price of the floor coverings themselves. gas boilers heating, inexpensive service and fuel efficiency, i.e. gas.
It is often difficult for a buyer to figure out on his own what kind of domestic boiler he should buy. An independent review of the equipment market, reviews of other consumers, and advice from professionals will certainly lead him to the conclusion that he needs to buy products from a domestic manufacturer - Lemax floor-standing gas boilers.
Our company is ready to offer competitive prices and a wide range of products manufactured according to modern technologies using components from leading global manufacturers. In particular, on heating boilers Lemax installs a gas burner device based on SIT safety automation. It ensures stable operation of the boiler and gas savings.
The Lemax enterprise produces several types of floor-standing gas boilers:
- - intended only for heating premises.
- - also allow you to provide heating of water for domestic needs.
- - with the ability to connect an indirect heating tank and remote control units.
Without exception, all products are distinguished by high quality and trouble-free operation for a long time. Correct operation of the equipment and prompt elimination of possible malfunctions in its operation are guaranteed by an extensive network of service centers. In almost all regions of Russia, they provide not only warranty, but also post-warranty maintenance of boilers, as well as resolution of all issues related to the purchased equipment.
Where to buy Lemax floor-standing boilers
We invite you to buy Lemax floor-standing gas boilers directly in our online store or contact a dealer in your region.
The Lemax boiler is made of high-quality 2 mm steel with increased flatness from the Magnitogorsk Iron and Steel Works. The heat exchanger is covered with heat-insulating enamel and treated with an inhibitory compound that prevents corrosion. The boiler does not require connection to the electrical network. PDesigned for heating and hot water supply of apartments, residential buildings, cottages, administrative buildings equipped with a water heating system with natural or forced circulation. The boiler meets all safety and environmental requirements established for this type of product. GOST 20548; TU 4931-011-24181354-2011.
The boilers operate on natural gas GOST 5542-96 and are supplied assembled with a gas burner device.
Operating water pressure in the heating system is no more than 2 kgf/cm 2, in closed system heating, it is necessary to install a safety system with a safety valve for a pressure of no more than 1.5-1.7 kgf/cm 2
- Expanded power range from 10 to 40 kW.
- New design.
- The presence of a protection system against overheating, interruption of draft, soot formation, as well as against blowing out of the boiler.
- Convenience of boiler maintenance due to the use of removable cladding elements and profile equipment.
- Ease of cleaning the boiler due to the use of a removable top panel.
- The safety protection system has been improved (a heat exchanger overheating sensor has been installed).
- Achieved maximum efficiency due to:
- increasing the heat exchange area;
- changes in the design of the turbulator for maximum retention of exhaust gases.
- Increased primary and secondary air flow.
- Hot water function.
- 3 year warranty.
Comparison table of technical characteristics
boilers
Lemax seriesPremium
| Name of parameters | ||||||||
|---|---|---|---|---|---|---|---|---|
| - single-circuit | 12,5 | |||||||
| - double-circuit | 12.5V | 16V | 20V | 25V | 30V | 35V | 40V | |
| Type of gas burner device. | GGU 12 | GGU 15 | GGU 19 | GGU 24 | GGU 30 | GGU 35 | GGU 40 | GGU 45 |
| Nominal heating capacity, kW | 10 | 12.5 | 16 | 20 | 25 | 30 | 35 | 40 |
| Efficiency % not less than | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 |
| Flue gas temperature °C, not less | 110 | 110 | 110 | 110 | 110 | 110 | 110 | 110 |
| Vacuum range at which stable operation of the boiler is ensured, Pa | 4-25 | 4-25 | 4-25 | 4-25 | 4-25 | 4-25 | 4-25 | 4-25 |
| Nominal gas pressure, Pa | 1300 | 1300 | 1300 | 1300 | 1300 | 1300 | 1300 | 1300 |
| DHW circuit capacity ∆ 30 °C, l/min. (at inlet water temperature of at least 15 °C) | - | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
| Maximum gas consumption, m3 | 1.2 | 1.5 | 1.9 | 2.4 | 3 | 3.5 | 4 | 4.5 |
| Maximum water temperature at the boiler outlet, °C | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 |
| Chimney diameter, mm | 100 | 130 | 130 | 130 | 130 | 130 | 140 | 140 |
| Gas pipe diameter, inch | 1/2’’ | 1/2’’ | 1/2’’ | 1/2’’ | 1/2’’ | 1/2’’ | 3/4’’ | 3/4’’ |
| Diameter of connected pipes, inch | 1 1/2’’ | 2’’ | 2’’ | 2’’ | 2’’ | 2’’ | 2’’ | 2’’ |
| Overall dimensions, mm: | ||||||||
| - Height | 748 | 744 | 744 | 961 | 961 | 961 | 1016 | 1016 |
| - Width | 330 | 416 | 416 | 470 | 470 | 470 | 532 | 532 |
| - Depth | 499 | 491 | 491 | 556 | 556 | 556 | 608 | 608 |
| Weight no more than, kg | 39 | 53/58 | 53/58 | 75/80 | 80/85 | 80/85 | 100/106 | 100/106 |
General Instructions
- Before using the heating boiler, please read this manual.
- Installation work, instruction for operation, commissioning, preventive maintenance and repair of the boiler are carried out by a specialized organization and local gas management in accordance with the “safety rules for gas distribution and gas consumption systems” approved by the State Technical Supervision Authority of the Russian Federation, and building codes and regulations SNIP 11-35 -76; SNIP 2.04.05-91 of the State Construction Committee of the Russian Federation, according to the project for installing the boiler and mandatory completion of the control coupon.
- The installed boiler can be put into operation only after its acceptance by gas industry specialists, instructions from the owner and the mandatory completion of an installation control coupon (page 21 of the operating manual)
- Checking and cleaning the chimney, repairing and monitoring the water heating system are carried out by the boiler owner. When replacing an old boiler with low efficiency with a modern one, you must pay special attention to the design of your chimney. When the boiler efficiency is below 80-85%, the flue gas temperature is about 200 °C, which ensures good draft even with a poorly insulated chimney. With an efficiency of 90%, the temperature of the flue gases drops to 110-120 °C, and, in the case of an outdated chimney, the draft disappears, which leads to the automatic operation and shutdown of the boiler. Failure statistics show that 94% of boiler problems are caused by an incorrectly installed chimney.
- Natural ventilation must be provided in the room in which the boiler is installed. It is prohibited to cover ventilation duct grilles.
- The use of boilers at hazardous production facilities is prohibited.
Installation, preparation for work
- The volume of the room in which the boiler is installed must be at least 8 m3. The distance between the boiler lining and the walls must be at least:
- Natural ventilation must be provided in the room in which the boiler is installed.
- When installing the boiler to the heating network, it is necessary to lay a sheet of non-flammable heat-insulating material on the floor, a sheet of iron on top, and install the boiler on it.
- The connections of the boiler to the heating system and the gas main must be threaded, allowing the boiler to be disconnected if necessary. If the boiler is installed to replace an old boiler, it is necessary to flush the pipelines and radiators of the heating system to remove rust deposits, scale and sediment. If these requirements are not met, deposit products (rust, sediment) are transferred to the boiler, which significantly complicates the circulation of the coolant and reduces the heat transfer of the boiler. In this case, claims regarding the temperature indicators of the coolant during boiler operation are not accepted by the manufacturer.
- If the heat consumption of the room is increased (the thickness of the external walls of the house, the integrity of windows and doors, the distribution of pipes of the heating system in attics, attics that are not insulated, its area is exceeded or the coolant capacity is significantly exceeded - the number of radiators, pipes) from those established by the standards, the temperature of the coolant may not reach 80 °C, which does not mean the boiler is defective.
- The coolant capacity in the heating system should not exceed:
Premium 10 - 150 liters
Premium 25 - 375 liters
Premium 12.5 - 180 liters
Premium 30 - 450 liters
Premium 16 - 240 liters
Premium 40 - 600 liters
Premium 20 - 300 liters
Warranty
The warranty period for the operation of the boiler, provided that mandatory annual preventive maintenance is performed and the consumer complies with the conditions of transportation, storage, installation and operation, is 36 months from the date of sale.