Round vibrating screens made of low carbon steel. Vibrating sieves type sv Vibrating sieve sv 1400 2

Four sizes developed vibrating screen SV:

vibrating sieve SV-0.4; vibrating sieve SV-0.6; vibrating sieve SV-0.9 and vibrating sieve SV-1.2.

The vibrating sieve is available in stainless steel or carbon steel.

Advantages of vibrating screens:

• high sieving efficiency
• the ability to select optimal modes for various materials
• high degree of maintainability. (replacement of the frame with mesh, if necessary, is carried out in 10...15 minutes)
• high reliability
• dust tightness of the device
• continuous operation
• low energy intensity
• low dynamic loads on the base

Features of the operation of vibrating sieves type SV:

A special feature of the operation of SV type vibrating sieves is the nature of vibrations of the sifting surfaces. Unlike other designs of vibrating sieves, vibrating sieves of the SV type use spatial (three-component) vibration of the sieving surfaces. This nature of oscillations ensures a continuous change in the magnitude and direction of inertial loads, which makes it possible to obtain optimal conditions sieving, especially for materials with particle sizes close to the mesh cell sizes. The three-dimensional motion of the screening surface combines the motion of the flat screen classifier and the screen.

Application:

In the food industry - factories for the production of milk powder, confectionery factories, oil and fat processing plants, meat processing plants, manufacturers of flavors and spices and many other enterprises; in the chemical industry - enterprises manufacturing welding electrodes, synthetic detergents, chemical fertilizers, PVC; in the construction industry - dry construction mixtures; in pharmaceuticals - for control sifting of drugs and in many other technological processes for sieving bulk materials.

Technical specifications

Technical characteristics of vibrating screens:

Technical description:

1 - cover, 2 - shell, 3 - mesh on the frame, 4 - unloading pipe, 5 - vibration isolator, 6 - vibration exciter, 7 - frame, 8 - electric motor

Vibrating sieve (vibrating sieve) SV is a single-mass oscillatory system of the over-resonance type, the oscillating parts of which include a housing with sieves, an unbalanced vibration exciter connected to the housing, which sets oscillations to the system. Rotation of the vibration exciter is transmitted from the motor pos. 8 through the coupling. The vibrating parts of the sieve rest on the frame pos. 7 through vibration isolators pos. 5.

The driving force of the vibration exciter is created by two unbalances rotating on a vertical shaft: the upper one, located approximately in the center of mass of the oscillating parts of the sieve, and the lower one.

The sieve vibrates with a frequency equal to the rotational speed of the motor shaft, and each point of the oscillating parts moves along a closed elliptical path located at an angle to the horizontal plane. The dimensions of the oscillation trajectory (horizontal and vertical amplitudes) depend on the magnitude of the static moments of the upper and lower unbalances.

The source material is fed into the loading pipe (see figure).

The fractions obtained after sifting leave the sieve through the discharge pipes.

The sifting intensity is regulated by the amplitudes and the rotation angle between the upper and lower unbalances.

The horizontal and vertical amplitudes of oscillations are regulated by changing the static moment, respectively, the upper and lower unbalances.

Vibrating sieves are a convenient and compact technique for mechanical fractional separation of bulk materials different types. Equipment of this type is suitable for sifting sand, crushed stone, microcalcite, marble, slag, coal, and solutions. Industrial vibrating sieves have repeatedly proven their effectiveness in the chemical, mining, and food industries.

Design features of vibrating sieves

The round multi-level vibrating sieves we present work on the principle of separating bulk products into fractions using a vertical deck system. The decks are mounted in a sealed housing equipped with openings for unloading the final product. The top of the device is tightly closed with a lid. Our vibrating sieves for bulk materials consist of the following elements:

• Screen deck with mesh or perforated sheet. The mesh size of the seeding surface varies depending on the classification stage.
• Electric motor with drive unit and eccentric blocks.
• Sealed housing with removable lid.
• Vibrating plate.
• Support frame with legs. Our products are stable even on uneven surfaces.

The design of the vibrating sieve for fine sieving provides for the installation of up to 5 mesh working parts. This arrangement allows you to sift sand and other bulk materials and obtain fractions of various sizes (0.1-15 mm). Finished product unloaded through special outlets in a round housing.

Our vibrating sieve for fine screening has compact dimensions and high productivity. The standard number of decks is 1-3 pieces, but if necessary, it is possible to install up to 5 working surfaces. Depending on the number of decks and their surface area, the productivity of vibrating screens for sand and other materials is up to 12 t/hour.

Round vibrating screens: buy at factory price

We offer products own production at reasonable prices with delivery anywhere in Russia. Products in standard versions are already in our database and are sent within 1-2 days after submitting an application. If you require custom-made devices or vibrating sieves with ultrasonic cleaning, we will produce them by prior arrangement. Our consultants will tell you more about the characteristics of our products by phone.

Vibrating sieve. Specifications

* - productivity depends on the type of material being processed and the size of the sieve cells;

** - the number of decks can be increased to 5 upon request;

*** - weight depends on the number of vibrating sieve decks.

With the help of our company's consultants, you can buy a suitable model of vibrating sieve at the manufacturer's price. Our catalog includes vibrating sieves SV-900, SV-1200, SV-1400 and SV-1700 with different screen surface areas and productivity.

Coarse cleaning means are mainly represented by mechanical vibration units (vibrating sieves), capable of removing large sludge larger than 100 microns. without significantly disrupting the pumping speed of the drilling fluid.

In shakers, cuttings are separated from drilling fluid using a screening device. Single-tier double vibrating sieves SV-2, SV-2B, LVS-1 and single-tier double-mesh vibrating sieves VS-1 are used. According to the principle of operation, all vibrating sieves are similar.

The figure shows a schematic representation of a vibrating sieve. Its main elements are as follows: a tray for collecting the purified solution 7, a receiver with a flow distributor 2, a vibrating frame 5 with a mesh 4, a vibrator 3, shock absorbers 6.

Vibrating sieve SV-2

There are no fundamental differences among the vibrating screens. Thus, the SV-2 vibrating sieve consists of a welded frame 1 with a receiving tank on which a distribution chute 2, two electric motors 3 are installed to drive a vibrating frame 5 and shock absorbers 6. Each of the two vibrating frames rests on four rubber shock absorbers and has a vibrator with a shaft eccentric , which is driven by an electric motor via a V-belt drive, covered by a guard 4. A working mesh is stretched between the drums 7. The grids are inclined horizontally at an angle of 12-18 degrees.

In BC-1, a replaceable cassette with grids is mounted on a vibrating frame. The vibrating frame is supported by four coil spring shock absorbers attached to the screen frame.

The frame consists of a base, two sidewalls, bolted together. The sidewalls are additionally fastened with a spacer, drive frame, and vibrator housing. The vibrator housing contains a shaft with imbalances that provide the required vibration amplitude. An electric motor is located on the drive frame, connected to the vibrator by a V-belt drive. On the opposite side of the drive frame there are weights that balance the drive.

During installation, vibrating sieves are installed on the cleaning unit circulation system above the container and secured with bolts. Deviations of the frame from the horizontal position are no more than 5 mm. A platform with a fence at least 0.75 m wide is installed around the vibrating sieve. The receiving pipe (chute) of the vibrating sieve is connected by a pipe to the wellhead. To bring the vibrating screen into working position, unscrew the four transport bolts securing the vibrating frame. Install the electric motor and put on two V-belts. When installing cassettes with mesh, check the presence of rubber protrusions on the base of the mesh and their correct location. The cassettes are installed in such a way that there are equal gaps on each side, after which the bolts are tightened with clamps until the spring coils touch.

The LVS 1 vibrating sieve with linear vibrations was developed by analogy with the best foreign examples of similar products. The linear single-tier vibrating sieve LVS-1 is designed for cleaning drilling mud from particles of drill cuttings when drilling oil and gas wells. Equipped with two flexible three-layer cassettes. Depending on the design of the equipment, the magnitude of the disturbing force of the vibrator can be adjusted.

Technical characteristics of vibrating sieve LAN 1

A linear vibrating sieve with one tier of filter meshes LVS-1K with rigid frame cassettes (hereinafter referred to as LVS 1K) is intended for cleaning drilling fluid from particles of drill cuttings when drilling oil and gas wells in a temperate macroclimatic region in accordance with GOST 16350. The temperature of the working environment during operation is not below 1°C.

The scope of application is in industries related to the purification of liquids from contaminants (mechanical particles), dehydration of sludge contaminants. Depending on the design of the equipment, the magnitude of the disturbing force of the vibrator can be adjusted.

Technical characteristics of vibrating sieve LVS-1K

Platform vibrators are installed on opposite sides of the frame at an angle of 180° relative to each other and create three-dimensional vibration of the vibrating screen. Changing the angle of inclination of the vibrators allows you to change the direction of vibration, and adjusting the location of the unbalances and adjusting the speed of rotation of the vibrators allows you to change the speed and productivity of the vibrating sieve. Thus, it is possible to change the nature of the movement of the product and the time it remains on the sieve, which allows the vibrating sieve to be used for sifting a wide range of powders with different particle sizes and shapes, bulk density, compactability and stickiness.

The bulk mass is uniformly fed through the upper central pipe using a feeding device (sluice or screw feeder, chain conveyor, dispenser, etc.) into the sieve. Successively passing through several sieves with different mesh sizes, the initial product is separated into fractions due to vibrations of the vibrating frame. Particles smaller than the sieve mesh pass through it, while larger ones are retained on the mesh and, under the influence of vibrations, are discharged through the side pipe. One vibration separator can have from 1 to 3 decks (sieves) installed, which ensures the separation of material from 2 to 4 fractions.

Buy a vibrating sieve at a bargain price You can contact our company "Prommash". For more than 10 years we have been successfully designing and manufacturing equipment for business.

Vibrating sieves are designed to classify bulk materials into particles of different sizes.

Vibrating sieves are used for bulk materials and powders to separate them into fractions. In the food industry, they are used for sifting powdered sugar, soda, table salt, milk powder, nuts, cereals, coffee, spices, sugar and other products.

Vibrating sieves are used in production building materials: for sieving lime, gypsum, fly ash, sand, kaolin, mineral powder. In the oil industry, vibrating sieves are installed to classify catalysts, in the paint and varnish industry for pigments and powder paints, in pulp and paper mills for sifting kaolin, chalk and starch, in woodworking industries for separating wood flour and sawdust into fractions.

In addition, vibrating screens can be used for screening crumb rubber, sieving copper, nickel, aluminum and other metal powders, corundum classification, etc.

Technical characteristics of the vibrating sieve:

Payment: 75% advance payment, 25% when the equipment is ready for shipment.
Equipment delivery time: 35 r/day.
Delivery: at the expense of the buyer by transport companies.

Working principle of vibrating sieve

The bulk mass is uniformly fed through the upper central pipe using a feeding device (sluice or screw feeder, chain conveyor, dispenser, etc.) into a sieve (or into a battery of sieves - depending on the design).

Successively passing through several sieves with different mesh sizes, the initial product is separated into fractions due to vibrations of the vibrating frame. Particles smaller than the sieve mesh pass through it, while larger ones are retained on the mesh and, under the influence of vibrations, are discharged through the side pipe. One vibration separator can contain from 1 to 4 decks (sieves), which ensures the separation of material from 2 to 5 fractions.

The three-dimensional motion of the screening surface combines the motion of the flat screen classifier and the screen.

Advantages of round vibrating screens

• the ability to select the optimal mode for a specific bulk product
• high sieving efficiency
• reliability
• dust tightness of the device
• maintainability (replacement of the frame with mesh, if necessary, is carried out in 10…15 minutes)
• continuous operation
• low energy intensity

CALL US AT THE PHONE PROVIDED TO BUY A VIBRATING SIEVE
OR REQUEST ADDITIONAL INFORMATION FROM OUR MANAGERS.

Guarantees:
We provide warranty and post-warranty technical support for sold equipment, information support for the client, and carry out any types of maintenance and repair work, including the production of necessary spare parts.

_____________________________________
We design, manufacture and supply various equipment, incl. and on individual orders from individuals or organizations.