Curtains with lambrequin (66 photos): luxury in the interior. Sewing a lambrequin: from creating a pattern to forming the finished product Lambrequins from thick fabric pattern

A lambrequin is a decorative part of a curtain that can hide a not very noticeable cornice. Beautiful lambrequins add completeness and consistency to the image of the window, and are a worthy frame for its top.

You can start making lambrequins with curtains in the kitchen. The window there is usually smaller than in the living room. Therefore, less fabric will be required, and making such a lambrequin is generally easier.

You will need the following materials and tools:

• Fabric – main and, if desired, lining fabric;
• Gasket made of non-woven material;
• The strip for the lambrequin is the length of the cornice;
• Decorative cord – 1m;
• Pencil;
• Furniture nails, hammer;
• Screwdriver, screws;
• Drill;
• Half a meter of tape.

A hammer can be replaced with a furniture stapler. The lambrequin for kitchen curtains can be made in ten steps.

A simple lambrequin for the kitchen:

• On the window you need to fix the bar 10 cm above the window opening, the margin on the sides will be the same;
• The fabric is cut along the length of the cornice + extra 10 cm;
• If you need the drapery to sag, for example, by 50 cm, then the fabric will need 70 cm;
• Seam allowance for drapery – 1.5 cm;
• To make a lambrequin rigid, you need a gasket and, if desired, a lining - they are cut according to the template of the main fabric;
• All layers are pinned and stitched, leaving 30 cm along the top edge;
• You remove the pins, turn them inside out, and sew the lambrequin by hand;
• The middle of the lambrequin and the strips are connected with a stapler;
• The remaining fabric is attached to the bar, the ends on the sides should hang down;
• The ends on the sides are ponytails, which are tied with a decorative cord, half a meter on each side.

All that remains is to tie the bows and arrange the folds. The lambrequin for kitchen curtains is ready!

Pattern and sewing curtains with lambrequin step by step (video)

Lambrequin for beginners: diagram and calculation

If you are still a beginner craftsman, you will need diagrams for the future lambrequin. This is important both in order to have something to focus on and for correct calculations.

You can draw the diagram on a scale of 1:10.

And now about how to calculate the fabric for a lambrequin for curtains:

• Let's say you decide to make a lambrequin with swags. Swags are decorative elements of curtains that are shaped like an inverted arc. If a lambrequin is sewn for curtains in the living room, there can be four swags - this is on average. Three swags will be large, and five, on the contrary, small.
• You need to calculate the length of each element, estimating how much one swag will overlap the next one. This is done according to a drawing to scale, or you will have to remember algebra and create an equation.
• This calculation can be illustrated using an example. Let the length of your cornice be 3.6 m (one of the most popular). And you need to make four swags for the curtains, so that each overlaps the adjacent one by one third. Three intersections of one third each will become the length of one swag, it turns out that the length of the cornice of 3.6 m should be divided not into four parts, but into three. It turns out that the length of one swag is 1.2 m.

Designers always make several lambrequin templates for curtains, and only then choose the one to work with.

Assembling an equilateral lambrequin swag (video)

Making lambrequins with your own hands

Let's say you decide to sew a simple, soft lambrequin for curtains. Its production will cost without additional decor, such as the same swags and decorative braid. Again, this is an option for beginners.

Manufacturing technology will be simple:

• Complete all calculations. Remember that the height of the lambrequin is also the seam allowance, and the width is the length of the cornice and the gathering factor. If you need light folds, then the coefficient is 1.5.
• Next, you need to cut the fabric so that you get a rectangle of the desired size. Finish the edges of the rectangle.
• On top part details, sew ribbon for curtains.
• Assemble by pulling out the required threads of the curtain tape.
• All that remains is to hang the lambrequin for this curtain on the cornice.

If such a production of a lambrequin still requires decoration, decorate the bottom with fringe, lace or a beautiful braid.

DIY lambrequin for the nursery

Curtains in a children's room always differ in design, color, and presentation. Today, lambrequins for such curtains, made in the form of a large appliqué, are in fashion. Basically, you can just sew a regular lambrequin for curtains, only without folds and asymmetrical. This will be a piece of the sky, which is naturally located at the top of the curtain. And onto this lambrequin you need to sew the sun and clouds, or vice versa, the moon and stars.

These can also be simple lambrequins made of thick fabric, the color matching the fabric of the curtains, and the lambrequins are attached to the cornice with loops. The fabric can also have an applique - a sun, flowers, a heart, a child’s name, etc. Such lambrequins for curtains will be both strict and cute. For example, fuchsia curtains and a lambrequin without folds, a shade lighter.

Asymmetrical lambrequins are not easy to sew yourself, and some craftsmen complement the fabric strip of the lambrequin with knitted openwork.

Square lambrequin (video master class)

A lambrequin is a nice decorative detail that, depending on the purpose, can make a window more comfortable, or pompous, or strict, or delicate. Successful endeavors and accurate calculations!

DIY lambrequins (photo)

Curtains on the windows not only make the room more comfortable and attractive, but also allow you to quickly and easily add uniqueness and originality. home interior. In order to hide defects in the window opening, curtain fastenings and cornices are used decorative panel, made of dense material and hung in front of the curtains - a lambrequin.

Lambrequin options

• Rigid (or bandeau). The material is attached to a rigid frame.
• Soft . Draped with ribbons or simply thrown over the cornice.
• Combined . A combination of hard and soft model.

Patterns for lambrequins

• Swags - semicircle with beautiful folds;

• Be sure to leave allowances: for the side edges and top edges, 2 cm is enough, for the bottom edges, at least 10 cm.
• Depending on the elements, allowances will be different. For example, for swag, a semicircle is drawn on paper and folds are laid, while at the same time calculating how much material is required to sew the panel. For a frill, the length in height is calculated experimentally, and then the number of frills is calculated horizontally.

Properly constructed patterns will help you avoid mistakes when cutting and calculate the amount of textiles needed.

Do-it-yourself rigid panel model

When choosing material for a box, they are guided by the rule: the heavier the panel, the stronger it should be.

• Textiles that are cut out according to a template, not forgetting to leave allowances along the entire length - 5 cm.
• Padded, thin foam. It is cut to the size of the panel with an allowance of 3 cm along the entire length.
• Lining fabric, cut according to a template with a 1.5 cm seam allowance along the entire length.
• Stapler and paper clips, glue.

• The padding is glued to the front and sides of the box. It is cut at the bends. Then the padding is folded back (left on the edge) and carefully glued.
• The fabric is placed on the prepared base. If a canvas with a large pattern is selected, then it is shifted to the center. The allowance (it should be about 2 cm) is folded over and secured with a stapler to the top of the box, starting from the center and moving towards the edges.
• Then do the same with the bottom edge, so that the fabric does not bristle at the bends; it is carefully cut. The bottom edge can be decorated with piping, then it is sewn on by hand.
• The lining fabric is applied to the inside with the right side up. The allowances are folded inward and secured with a stapler.

DIY openwork lambrequins

For sewing, a thermal bando is used as a base.

• Select a design and prepare a pattern. To do this, draw a pattern on paper and cut it out. Then they transfer it to the fabric and cut it out again.
• The finished pattern is glued to the thermoband, carefully straightening it.
• After this, the lining is attached to the wrong side. If the pattern is complex, then it is fixed to a special adhesive web.
• All edges are treated with a zigzag seam to prevent the material from fraying. You can also decorate the edges with decorative cords and braid.

How to sew a soft model with your own hands?

• Take rectangular fabric along the length of the curtain.

If folds are planned, then the material should be 1.5 times longer.

• The bottom and sides are hemmed, and loops are sewn on top for fastening. The product is ready.

Features of lambrequins for the hall

WITH various options lambrequins for the living room can be found in the video:

The more elements, the more luxurious and interesting the design looks. However, in a small room such a design will look bulky and awkward. Therefore, read the article on how to choose the right curtains for your interior:.

Features of lambrequins for the kitchen

For the northern window you should choose transparent lightweight fabrics, for the southern window - dense textiles.

• A narrow rectangular canvas decorated with fringe or tassels. But, if the fabric is colorful, then you will have to refuse additional decoration.
• Rigid model, decorated with a contrasting small appliqué.

Lambrequins are more decorative than practical. This interior element is designed to hide the connection between the curtain and the cornice and add elegance to the window space. A lambrequin can be hung in absolutely any room, but choosing such textiles for the kitchen is especially difficult. Here, all elements must correspond to a lot of characteristics, and at the same time not clutter the interior. How to choose a lambrequin for the kitchen - read on.

Lambrequins are designed to give the room beauty and comfort. They hide the junction of the cornice with the curtains, which makes the window space more neat.

Such interior elements are usually used in interiors with a classic or romantic design. In rooms designed in high-tech style, such elements are used extremely rarely. If you decide to issue kitchen windows in a gentle pompous style, then lambrequins will be excellent helpers for you.

What types of lambrequins are there:

1. Soft lambrequins are made from the same fabric that is used for sewing curtains. Such products fall in soft waves and make the window more elegant.
2. Hard lambrequins are made from front and lining fabrics. In another way, such products are called bando. Also, rigid lambrequins can be made from a combination of cord and wire. They usually have an openwork or floral pattern.
3. Combined lambrequins combine a hard and soft product. They are especially beautiful and stylish, so they can be used in any interior.

These types of lambrequins can be used with different types curtains However, soft products look especially good with tulle, and hard ones with thick and straight fabrics. A combined lambrequin can be used to decorate almost any textile.

When choosing curtains for a kitchen lambrequin, remember that Roman, Japanese, roller curtains, and blinds will not suit you.

What are the curtains for the kitchen with a lambrequin made of: photos and design ideas

The lambrequin should fit harmoniously into the interior. It should match the color of the rest of the room elements, as well as the shade of the curtains.

Also, the lambrequin should be selected depending on the size of the window. Often the windows in the kitchen are small, so lambrequins with a large number of decorative elements do not fit there.

For small windows you need to choose accessories not exceeding 1/5 in size window frame. The fabric should not be very bright and should not have large drawings and patterns.

A narrow rectangular lambrequin with a small amount of short fringe is perfect for a small kitchen. You can also purchase a small wavy accessory with tassels on one side.

Rigid lambrequins are an excellent option, suitable for small window. They do not take up much space and do not take up unnecessary free space.

Combined asymmetrical lambrequins, if chosen correctly, can also decorate a window. It is desirable that the soft fringe be located only on one side of the lambrequin.

You can find even more ideas for decorating curtains in rooms on the website:

Lambrequin height

A lot depends on the size of the lambrequin. From the right choice The height of this element will determine how large the window will appear. Also, do not forget about the influence of the shape and type of such a product on the layout of the room.

The height of the lambrequins directly depends on the size of the window and the height of the ceilings. For windows that are less than a meter high, you cannot use lambrequins with a large number of decorative elements, since such accessories reduce the already small space.

Windows in the kitchen are rarely large, so the lambrequins with which they are decorated should not occupy more than 1/5 of them. If you want to raise a low window, you can hang the cornice 15-20 cm above the opening and use a 40-50 cm lambrequin to decorate it.

You can also choose the width of the lambrequin depending on the height of the ceilings. So, in apartments with ceilings up to 3 meters, airy products with a width of 30-40 centimeters will look most appropriate. For ceilings with a height of 3 meters, you can choose half-meter lambrequins. If you have ceilings lower than 2.6 meters, then you should not choose accessories wider than 15 centimeters.

What are they? How to make it yourself? How to find out about new products? You can read all the answers to questions about lambrequins in one article:

How to sew a lambrequin on one side with your own hands

Specialized stores sell the most interesting and fashionable new lambrequins. However, their price is often quite high. If you want to get an interesting and stylish lambrequin that is perfect for your kitchen, then make it yourself. This kind of work will not take you much time, but will bring a lot of pleasure.

How to make a combined asymmetrical lambrequin with your own hands:

1. Cut out a stencil of the rigid part of the lambrequin. It should have a width of 15 to 25 cm. You also need to add the size of the girth of the cornice on top.
2. Using a stencil, cut out one element from the quilted fabric, two mirrors from the front fabric, two mirrors from the adhesive web and one from the adhesive interlining.
3. Assemble the hard lambrequin in the following order: front element, adhesive web, quilted fabric. Iron the resulting sandwich so that all the parts stick together.
4. Sew a tulle element in a semicircle to the quilted fabric on one side of the lambrequin. At the same time, such a tulle part should start from the center and be larger on one side.
5. Assemble the remaining elements in the following order: web, interlining, face fabric.
6. Sew Velcro to the top of the resulting product. In this case, the soft halves should be on top, and the hard ones near the beginning of the carved ornament.

This product is not at all difficult to make, but it looks very interesting. This type of lambrequin is suitable for a small window in the kitchen. However, by increasing the size of the svarga, you will get a product suitable for decorating a large window frame.

You can also make a lambrequin exclusively on a rigid base. To do this, you need to follow the steps described in points 1-3, skip point 4, and then follow the instructions in points 5 and 6.

Soft lambrequins are more difficult to make. Usually several types of fabric are used for them. different colors. You need to sew semicircles, frills and molds together, and also organize the fastening of the element to the cornice.

Soft lambrequins for the kitchen (video)

Lambrequins in the kitchen are not the most necessary element. However, they will give the room greater elegance and luxury. Make such an accessory with your own hands, and it will delight you for many years!

Lambrequin design for the kitchen (interior photo)

Window- peculiar eyes of the house. These are structural elements that connect the interior space of a structure with the outside world, sources of natural light and fresh air. Such multifunctionality of windows requires the creation of a decent frame for them. Lambrequins will cope well with this task.

— decorative element, can act as an independent window frame or be used in combination with curtains and curtains. The variability of product models allows you to choose the right element for any interior.

Lambrequins are sold ready-made or made to order. The price of this decorative element is not always affordable - it depends on the complexity of the design. Therefore, many housewives have a question: is it possible to sew this accessory yourself?

Manufacturing a product can be either simple or complex - it all depends on design features models. Let's look at their main varieties.

What can a lambrequin be like?

- a horizontal textile element of the window frame, located in the upper part of the structure. He can be:

• Soft- a decorative element made of thin and thick curtain fabric. The panel of the product can be straight or folded,
  the lower edge is smooth, curly.
  To decorate it, sewn details are used (beads, flowers, bows, fringe, lace, contrasting edging), fastening elements (loop loops, ties), folds of various shapes, voluminous textile elements (slips, swags, bells, de jabot, ties);

• Combined- combines soft and hard elements. The product may consist of a dense figured base, complemented by parts formed from thin fabric;

• Figured- a product with a three-dimensional pattern, holes of a specific shape. Its varieties are openwork lambrequins, the pattern on which is burned out using laser equipment. Such products are highly decorative and do not weigh down the space.

During their existence, lambrequins have changed significantly. Their shape has become more diverse, and new decorative elements have appeared. Today there are lambrequins:

1. Straight;
2. Folded (wavy, bow-shaped, cylindrical);
3. teardrop-shaped;
4. Asymmetrical;
5. Arched;
6. With and without edging;
7. Royal - consisting of many decorative elements (swag, de jabot, folds, molds).

On a note: These are not all types of lambrequins. This decorative element can be presented in various designs.

Learning to make a lambrequin yourself

Before you start making the product, you need to decide on its model, whether it will be supplemented with curtains or curtains or not. Appearance The product depends on the purpose of the room in which it will be used, the style of the interior, and the desired functionality.

The size of the lambrequin is also important - what part of the window opening it will cover. The degree of natural lighting in the room depends on this. It is also important to correctly determine your own capabilities: whether you can make complex patterns and connect the details of the composition.

Product sizing

In order for the lambrequin to be a worthy window frame, it must match the size of the opening. Several aspects are taken into account:

• As a standard, the width of the lambrequin should be 20-25 cm longer than the rod on each side. This will provide additional protection from sunlight and give the product a finished look;
• if it is intended to produce a folded lambrequin, then its width should be at least 1/3 longer than the cornice, the optimal indicator is double the length of the rod;
• The height of the lambrequin depends on its model and personal preferences. As a standard, the panel covers 1/3 of the opening. But its height depends on the wall above the window - for aesthetic reasons, the lambrequin should completely cover it.

Fabric selection

Color solution The lambrequin is determined by the style of room decoration. The best option- matching furniture upholstery. This will allow you to combine all the textiles in the room into one interior composition.

On a note: A lambrequin can also be an accent in a room - in this case it is sewn from fabrics of bright, rich colors.

Deciding on the form

Fabric consumption and the complexity of making a pattern depend on the shape of the product. The lambrequin can consist of several sections. The complexity of the design depends on the length of the cornice, your cutting and sewing skills.

Features of product design, making a lambrequin pattern

A single-section lambrequin should fill the entire cornice. If the product consists of two elements, then one overlaps the other by 1/3. When making a lambrequin consisting of 3 sections, the length of the rod is divided by 7 and multiplied by 3. The resulting indicator is the width of each section.

Let's calculate it using the example of a cornice 150 cm long: 150/7x3 = 64 cm. It turns out that the lambrequin should consist of three sections 64 cm wide, which overlap each other in 2 places by 1/3. If there is more overlap of elements, the folds will break and the drapery will lose its shape and harmonious appearance.

If in a certain lambrequin model the swags do not overlap each other, but are arranged in a row, the space between them is covered with small decorative elements (bells, ties, molds). This will hide the ends of the cords formed after the fabrics are pulled into folds.

The de jabot element allows you to visually adjust the height of the premises. It is used in combination with swags. If its cut starts just above the bottom point of the swag, it adds height to the room, if lower, it brings the ceiling closer.

Advice: It is convenient to draw patterns for a lambrequin on a large table or wall. The first is the horizontal line - the width of the central section. Proportionally, the contours of the side elements are applied on both sides of it.

Instructions for sewing a one-section lambrequin

One of the easiest to make is the “Scarf” lambrequin model. This decorative element can be used to decorate a window in the kitchen. And if you add it classic curtains— this set can be hung in a bedroom or children’s room. Structurally, it is a one-piece fabric, manually draped on a cornice.

Attention: Since the lambrequin model is distinguished by its simplicity, no patterns are required for its manufacture; markings can be made directly on the fabric.

To determine the size of a product, two indicators are needed:

• Length of cornice;
• Sag height

Important: the swag (sag) in the product should occupy no more than 1/6 of the opening, otherwise window design will shade the room.

Marking is done in the following sequence:

1. Mark the desired height of the lambrequin;
2. The fabric is folded in half, from its middle along the upper edge, ½ of the length of the cornice is marked in both directions, along the lower edge - the height of the sag;
3. The top and bottom points on each side are connected, defining the line for sewing the braid;
4. Along the upper edge of the lambrequin, the height of the folds is added to the width of the cornice. From extreme point draw a line perpendicularly down. To the resulting rectangle, add side allowances for hems (2 cm each).

The fabric is cut along the intended contour and folded on all sides. Thin curtain braid is sewn along the upper edge, equal to the length of the cornice and diagonal lines. Where the tape runs diagonally, it is carefully pulled together by the cords. As a result of this action, a central swag with folds in a semicircle and side folds are formed. The lambrequin is ready to be hung on the cornice.

Advice: The places where the product is tied can be decorated with sewn-on decorative elements (flowers, butterflies).

Making a two-element lambrequin

A living room or bedroom will be adequately decorated with a two-layer lambrequin, consisting of a long and short panel, gathered into elegant folds. This design looks harmonious with sliding curtains made from the same fabric.

Advice: the bottom layer of the lambrequin can be made from a material that is several shades lighter than the rest of the window frame details - this will highlight the horizontal decorative element against the background of the overall composition.

The set consists of:

• Thin translucent curtains;
• Sliding curtains with tiebacks that fall to the floor;
• Two-layer folded lambrequin.

Examples of patterns for all elements of this window frame are presented in the diagram below. The finished structure has dimensions of 3.5 x 2.8 m.

The lambrequin will be curtained on a curtain rod 350 cm long. To form folds, you will need mounting tape with a gathering factor of 3. The product is made from two rectangular pieces of fabric measuring 70x1050 cm and 90x1050 cm. First, their edges are processed, and a fold is made along the upper edge to the width of the mounting tape.

After this, the curtain braid is attached, on which wavy folds are formed by tightening the cords. They can be one-sided, counter or bow - depends on your skills. The simplest option- waves directed in one direction.

Features of sewing a lambrequin from three elements

The product consists of a central swag and two side cascading elements. It is fixed on the cornice board.

To make a lambrequin you will need:

• Medium weight fabric;
• Curtain board;
• Curtain tape;
• Scissors, pins, thread, needle;
• Small nails, hammer;
• Sewing machine.

First we cover the curtain rod with fabric. Next, we begin making patterns for the lambrequin parts. Their dimensions are calculated for a cornice 2.8 m long.

We place the paper blanks on the fabric folded diagonally and attach them with pins. We trace their contours with chalk/pencil along the fabric, leaving allowances of 1.5-2 cm for the folds. Since the folds on the lambrequin will be formed using curtain tape, we therefore leave such an allowance along the upper edge of all its elements so that a hem can be made equal to the width of the tape.

We sew braid to the side edges of the swag and tighten the cords, forming folds. Now let's start designing the cascading elements. We sew the tape to their upper edge and assemble the fabric. We align all the parts of the lambrequin along one line and secure them with pins so that they slightly overlap each other. We fasten the lambrequin to the board using small nails.

Secrets of simple but successful drapery

The window will be effectively decorated with a lambrequin, which consists of a mechanical crossover that smoothly turns into a de jabot. The product consists of a single rectangular piece of fabric. The secret of its presentable appearance is its elegant drapery.

The central element of the lambrequin is a large crossover, forming two symmetrical swags, separated from the side elements of the structure (de jabot) using a curtain tape. The braid allows you to form folds on it. The swag is attached to a bar in the form of a crossover, then the side parts of the product are decorated, and their top points are decorated with applied flowers - the result is simple and beautiful.

Elegant drapery can be created even from straight fabric. To do this, sew an arched lambrequin on a contrasting lining. Most of the panel is attached to the cornice using metal clips on rings, the rest is designed as a crossover. The product is complemented with a flower made from the same material as the lining.

Advice: fringe sewn along the lower edge of the lambrequin will emphasize the unusual shape of it.

Another way to simply but effectively drape a window is with a lambrequin consisting of three separate sections. The basis of the design is two triangles, sewn from thick fabric, which have a drawstring for threading the rod. One grommet is inserted into them to fix the connecting element.

It is a rectangular piece of thin fabric (organza), several tones lighter than the main one. It is processed along the contour with bias tape and threaded through the holes of the eyelets. The result is a one-piece design: two elements of the lambrequin are connected with an elegant swag, and beautiful flowing folds are formed on the sides of the product.

A window decorated with a lambrequin always looks unusual. And if you complement this element of textile decor with curtains, you will get a presentable, stylish and quite functional design. Depending on its model and color, it can be used to decorate a kitchen, nursery, bedroom, living room or office. Sewing a lambrequin is not difficult, because there are simple styles of the product that look very impressive. All you have to do is find a suitable pattern and realize your idea.